Show calling software

Call every cue from one screen.

Your show caller gets a live calling script built from the run of show: every cue with its department, its standby and its go, in order, with the clock beside it.

  1. Write cues into the run of show
  2. Stand by each department
  3. Call go, and the next cue loads
See the calling tools

The calling script and the clock, side by side.

Show callers juggle a paper script, a stopwatch and a headset. PresenterCue puts the cue list, the countdown to the next segment and the producer’s notes on one screen, and marks each cue as called so nobody loses their place.

What does a show caller do? →
PresenterCue calling script on a phone, with standby cues for lighting and video

Warning, standby, go: the language software has to respect.

Calling a show has a grammar that predates software. Theatre stage managers give three kinds of call: a warning, a standby and a go. A light cue might be called “Warning LX 24”, then “Standby LX 24”, then “LX 24, go”. The department and number come first and the word “go” comes last, because “go” is the word operators act on.

Operators answer standbys so the caller knows they’re ready: “Standing by”, or just “Lights”. PresenterCue’s calling script follows that grammar instead of inventing its own, so a caller trained in theatre or corporate events can read it without a manual.

Phone showing the warning, standby and go calls for lighting cue 24

Built for the calling position

The tools a show caller reaches for, in the order they need them.

How long before a cue should the standby come?

Long enough for the operator to get ready, short enough that they’re still focused when the go arrives. Stage management teaching material from Oberlin College puts it at a few lines or about ten seconds before the cue.

Consistency matters more than the exact number. If standbys arrive at random intervals, operators either relax too early or panic too late. For cues tied to the clock, PresenterCue shows a countdown beside each one, so the caller can stand by at the same interval every time.

Fact card: a standby is commonly called about ten seconds before its cue

Software for the caller, not instead of the caller.

There’s a difference between show calling and show control. Show control software and consoles execute cues: they play the sound, run the video, fade the lights. Show calling is a person deciding the moment, because the moment depends on a speaker’s pause, a laugh or a late walk-up.

PresenterCue stays on the calling side of that line. It doesn’t send triggers to your consoles. It gives the caller the script, the timing and the producer’s changes, and leaves the go to the person on headset.

Phone showing the show caller calling cues and operators executing them

FAQs

How show calling works with PresenterCue.

What is show calling software?

Show calling software gives the show caller a live, ordered list of every cue in a show, tied to the timing, so they can stand by and call each department at the right moment. Read what is show calling for the basics.

Does PresenterCue trigger lighting, sound or video?

No. PresenterCue doesn’t send control signals to consoles or playback systems. The caller still calls the cue on comms and each operator executes it. PresenterCue keeps everyone working from the same script and timing.

Does it work with our headset system?

Yes. PresenterCue runs on a screen at the calling position, beside whatever comms you use. It doesn’t need to connect to your headset system.

How should cues be numbered?

Most teams number cues per department, such as LX 14 or SND 8, and keep the numbers in the run of show so the caller and operators use the same names.

What happens when the show changes live?

The producer edits the run of show and the change appears in the calling script, flagged, so the caller knows what moved before they reach it.

Can a backup caller follow along?

Yes. A second person can open the same calling script and see which cues have been called, so they can take over at any point.

What’s the difference between show calling and show control?

Show calling is a person telling each department when to act. Show control is software or hardware that executes cues automatically. Many productions use both: a caller decides the moment, and a control system plays the cue.

Should I say “lights” or “LX”?

Both are common. “LX” is widely used in UK theatre and many corporate crews; others say “lights”. Pick one, write it in the run of show and use it on every call.

What is a warning call?

An optional early heads-up before the standby, such as “Warning LX 24”. It’s common in theatre for complex cues; many corporate callers skip it and go straight to the standby.

How do you call several cues at once?

Stand them all by, then give one go that names them, such as “Lights and sound 45, go”. For a fast sequence, call each go in turn after a single group standby.

Sources for this page

1. Wikipedia: Cue (theatrical)
2. Oberlin College stage management project: How to run tech
3. LibreTexts, Technical Theatre Practicum: Cueing scripts
4. Theatrecrafts: Calls, cans and comms

Give your caller a better script.

Build the cues once, in the run of show, and call them live.

Script

Calling script

PresenterCue feature

Calling script

The calling script is generated from the run of show, so the cues the producer planned are the cues the caller sees, in the right order.

Built for
Show callers
Source
The run of show
Replaces
Paper scripts

What you get

  • Cues in running order
  • Segment headers and timings
  • Notes beside each cue
  • Big, readable text in a dark booth
Script

Department colours

PresenterCue feature

Department colours

Each department has its own colour and prefix, so the caller can read a block of cues at a glance and call them together.

Built for
Show callers
Departments
LX, SND, VID, STG and custom
Shows
Prefix and colour

What you get

  • Custom departments
  • Cue numbers per department
  • Grouped cues called together
  • Filter to one department
Cue

Standby and go

PresenterCue feature

Standby and go

Put departments on standby ahead of the cue, then call the go. The screen shows which cues are standing by and which come next.

Built for
Show callers
States
Standby, go, done
Language
Your house style

What you get

  • Standby list always visible
  • Next cue highlighted
  • Countdown to timed cues
  • Visual cue reminders
Cue

Called-cue tracking

PresenterCue feature

Called-cue tracking

Each cue is marked as called, with the time it went. If the show jumps, the caller can skip ahead and the script follows.

Built for
Show callers
Records
Time each cue was called
Helps
Debriefs and reruns

What you get

  • Mark cues as called
  • Skip or repeat a cue
  • Timestamped log
  • Pick up where a backup left off
Team

Producer notes

PresenterCue feature

Producer notes

When the producer cuts a segment or moves a cue, the change appears in the caller’s script with a note, before it’s needed.

Built for
Producers and callers
Delivers
Live changes and notes
Replaces
Shouting over comms

What you get

  • Change notes on cues
  • Cut and moved segments flagged
  • Notes from any role
  • History of what changed
Team

Crew view

PresenterCue feature

Crew view

Operators can open their own department’s cue list and follow the caller, so they’re ready before the standby comes.

Built for
Lighting, audio and video operators
Shows
Their department’s cues
Needs
A browser

What you get

  • Department-only view
  • Live position in the show
  • Notes for each operator
  • Works on a tablet at the desk

Share this page

Send this page to someone who runs live events.